This is long overdue but here we go. Here’s all the information for the renovation of the RV from front to back, top to bottom…
Part 1 covers: Floors, Ceiling, Windows, Cab, Dining and Kitchen.
First we had to remove all the old wallpaper, there was a lot! The easiest way to do this was score the paper in thin strips, then use a heat gun to warm up the paper and slowly peel off very time consuming!
Next the whole interior of the RV was repainted. I used Zinser 123 primer which wasn’t great, it took soooo many coats to cover (I think I painted 8 or 9 coats). The white top coat is Behr Ultra Premium White.
We replaced the old carpet with click and lock vinyl from Lumber Liquidators, Clear Lake Chesnut, easy installation and we used an additional adhesive just to be safe (Loctite 2 in 1 seal and bond)
For the ceiling I chose a wallpaper Frond pattern from Anthropologie. I love the bold design and plant anything is good by me. It was surprisingly easy to install. The wallpaper was pre glued so we wet the back with water using a foam roller and it went up quick.
One downside to wallpaper on the ceiling of the RV is that the Winnebago is always moving, vibrating while we drive and flexing with temperature changes. Because of this there are a few areas where the wallpaper has ripped and it buckles every now and then depending on the temperature.
I spray painted all the window trim black with an appliance spray paint as well as the screws. Quick tip: push the screws into cardboard to easily paint the tops.
For window coverings we used custom cut white roller blinds from home depot and for the larger windows I made window coverings out of felt and attached magnets around the edge so they can be easily hung and removed during the day for a cleaner look. They required no sewing at all! The magnets were sticky on one side so they were easily attached as well.
The lock on the front door was the standard lock that came with the RV and we quickly discovered that ANY key could unlock it. We decided to get an electronic keyless lock and tried two different ones. The first was terrible and broke almost immediately it was the AP Products 013-509 Electric Travel Trailer Lock. The second one is much better and so far we are really happy with it: RVLOCK KEYLESS CLASS C/A STYLE ENTRY HANDLE
We used FLOR carpet tiles to replace the old carpet in the cab Tailored Touch. It was fairly easy except for the area that covers the engine (the dog house) Tim had to cut a TON of slices to wrap around the curved edges. We used an adhesive to attach the carpet and a brad nail gun.
The chairs were tough to cover and I had my mom assist me because I have no patience when it comes to sewing. We ended up using an old blanket and made slip covers for the top part of the seat, for the bottom I laid sheep skin throws from Cowboy Kate.
The rest of the cab area was in great condition. We added a backup camera which we keep on all the time in replacement of a rear view mirror. It is so helpful and necessary. We found it on Amazon and Tim installed it.
For the table I chose an acrylic top and had it custom made to fit from a local plastic company. It really helps keep the space feel open and although it does scratch a little it’s worth it! Installing acrylic can be tricky because when you put screws through it you run the risk of cracking. We slowly drilled pilot holes with a dull drill bit prior to screwing it down to prevent this from happening.
The table leg was found at the reclaim it store in Portland and to reinforce where the leg meets the table we added a longer piece of wood cut into a nice shape and secured with screws.
There was storage under the dining benches (which were original to the space) but the only way to access it was to remove the cushions and seats. We decided to add a pull out drawer for easy access on one side (thanks for building that dad!) On the other side we added a cabinet drawer where we could access our safe (a must have for keeping valuables).
We replaced the old sink with a new white plastic one made for RVs, nice and lightweight. The faucet is from Rejuvenation and although heavy (we tried to keep in mind the weight of everything we used because the heavier the RV gets, the worse the gas mileage) completely worth it for the style it brings!
The black and white wood pattern wallpaper is from Hygge & West. I hung that one up by myself and it didn’t go as well without Tim giving me direction. I cut out the window shape and then hung the paper, I should have hung the paper first and then cut out the window… Oh well, you live you learn. This one needed an adhesive I applied with a brush. Now that it's up you can't even notice my mistakes.
The wood triangles next the the stove were cut out of thin ply wood and painted with a clear coat of poly then glued to the wall with the same Loctite used on the floor.
We replaced the counters and made new ones out of plywood. Tim cut an extra piece for the edge to make it look thicker than it actually is. We used a clear poly to finish.
For all the cabinets I chose leather pulls with gold details from Rejuvenation and then drift wood that I found for the larger cabinets.
In the interior of the cabinets we built additional dividers to maximize the space.
Now for the best part. Before and after shots!
That's all for part 1, part 2 coming soon!!